Skip to content Skip to sidebar Skip to footer

Widget Atas Posting

Welding Machines - What Is Duty Cycle & How Is It Calculated? Define Welding Duty Cycle

Hallo ! Welcome to the a site all about welder, This a site was created as a means to provide a variety of education, especially relating to welder activities. at this meeting author will explain circa"Welding Machines - What is Duty Cycle & How is it Calculated?" clearly, get moving see in detail...

Welding Machines - What is Duty Cycle & How is it Calculated?

Welding machine duty cycle

What is Duty Cycle?

Duty cycle is the percentage of time that a machine will safely operate (or weld), within a certain time period, at a given amperage. For example the Weldforce WF-205MST multi-function welder has a duty cycle of 200 Amps @ 30%. This means that it will operate at 200A for 3 minutes within a 10 minute time period.  For the remaining 7 minutes, the machine will switch to thermal overload to cool down.

All welding machines are (or should be) fitted with thermal overload protection which means the machine will cut out when internal critical components reach a certain temperature, to prevent damage. The machine will then re-start when it returns to a safe temperature.

Duty cycle will change at different amperages. At higher amperage output the machine will heat up more rapidly, and the duty cycle will reduce.  At lower amperages, the duty cycle will increase.

For example - if we look at the WF-205MST machine again;

Duty cycle at 200 amps = 30% 

Duty cycle at 145 amps = 60% 

Duty cycle at 110 amps = 100% 

How is duty cycle calculated and tested?

While the basic formula is always the same (% of "on" time within the test period), there are several variables which can influence the outcome of a duty cycle test, including:

  • Time period over which it is measured (generally 5 or 10 minutes – a 10minute period is more demanding).
  • Ambient temperature in which the test was made (a higher ambient temperature is more demanding).
  • Whether the test was with a 'fresh’, cold machine or a machine that was already warmed up from prolonged use. (Testing a machine that is already hot is obviously much more demanding on its cooling system.)

The most widely accepted standard for testing and determining duty cycle ratings is the European Standard EN60974-1, on which the Australian standard AS60974-1 is based. This standard is very demanding and is therefore considered to be the best indication of how a machine will perform in ‘real life’ conditions. All Weldforce machines by Weldclass are tested to this standard.

Welding Machines - What is Duty Cycle & How is it Calculated?

Again, take the example of the Weldforce WF-205MST with a duty cycle rating of 200A @ 30%. To achieve this rating under the EN60974-1 standard, firstly the machine was ‘warmed up’ prior to testing by welding continuously to cause it to cut out on thermal overload at least twice. Then it was tested in a controlled chamber heated to 40C. Over a 10 minute period it was then able to weld at 200 Amps (which on this machine is maximum output) for a total of 3 minutes... hence the duty cycle rating of 200A @ 30%.

Are all welding machines duty-cycle tested in the same way?

Unfortunately not all machines are tested to the EN/AS60974-1 standard and therefore it can be difficult to compare the duty cycle ratings of some machines versus others. For example, if the test on the Weldforce WF-200MST was conducted over only 5 minutes and/or with a cold machine and/or at a lower ambient temperature, the rating may well have been 200A @ 50-60% which would be unrealistic and misleading.

All Weldforce machines by Weldclass are duty cycle tested according to EN/AS60974-1 which means that the quoted duty cycle ratings accurately represent how each machine will perform in ‘real life’ conditions.

Is Duty-Cycle the best way to judge the performance of a welding machine ?

Yes and no!

Duty cycle rating - providing that it is accurate and not over-rated (as is sometimes the case) - is a useful indication of how a welding machine will perform in terms of output and capacity (or productivity).

However, duty cycle should not be considered in isolation.

Just as you would (normally) not make a decision to purchase a motor car based only on it's top speed (say without considering aspects like handling, acceleration, safety, etc)....  in the same way, there are other factors to be considered when it comes to welding machines.

Firstly, the welding process itself can alter the importance of duty-cycle. Having a higher duty cycle can be important for MIG welders, but may be less important for Stick/MMA and TIG. See further information on this below.

The subject of power draw, power supply and the efficiency of the welder also add another dimension to the duty-cycle subject. 

This is especially the case with single-phase (240V) welding machines, where the machine (according to the AS60974-1 standard) must have an effective input current draw (I1eff) equal to or less than than the rated power supply that the machine is designed to operate on - commonly either 10A or 15A. 

Often, this requirement is the restriction (or "ceiling") on duty-cycle, more so than what the machine is actually capable of. For example the Weldforce WF-180MST MIG welder, has a duty cycle of 10% at maximum output of 180A. This machine is actually capable of significantly higher duty-cycle, but in order to be suitable for 10A power supply the ouput and duty cycle have been restricted, or capped.

Welding Machines - What is Duty Cycle & How is it Calculated?

This is why machines with greater efficiency offer an advantage (especially 240V 10A/15A single phase machines). Through greater efficiency they can deliver a higher output and duty cycle, from the same level of power input.

The following machines by Weldclass incorporate "PFC" technology, which greatly increases efficiency and gives them a higher duty cycle;  Weldforce WF-205MST and WF-255MST MIG/Stick/TIG welders, and Cutforce CF-45P Plasma Cutter.

The importance of Duty Cycle in different welding processes

While duty cycle is never "un-important", different welding processes will place higher or lower demands on the welding machine in terms of productivity or duty cycle.

The following comments are from a 'rule of thumb' perspective and may be a guide on how much emphasis to place on duty cycle ratings - vs other factors and features - when chosing a suitable welding machine.

Please note that every application is different and the general comments here may not always apply to your situation.

Duty Cycle & MIG Welding

Being an automatic process (eg the filler metal is fed automatically), a MIG operator has the ability to weld for long periods of time with minimal "off" or "down" time between welds. 

Of course this varies from one application to another. 

In production situations, for example where jigs may be used to minimise set up & maximise "welding time", duty cycle can be very important. When it comes to selecting the right welder, opting for a welder that has "too much" capacity, rather than "just enough" is a wise decision.  For example, your application may involve production welding of up to 8mm steel. In theory a 200 amp welder, such as the Weldforce WF-205MST is capable of this, however in a production situation a 250 amp machine (like the WF-255MST) will offer more duty cycle. (At 200 amps, the WF-255MST has almost twice the duty cycle of the WF-205MST).

In maintenance applications, duty cycle may not be so critical, because "Welding time" % is typically lower. Often the operator may run just 1 or a few welds before having to do other taks prior to resuming their next weld.  

Duty Cycle & MMA (stick) welding

Becuase MMA/stick welding is a very manual process - involving changing electrodes, chipping slag, etc - the % of time that the operator spends actually welding is typically a lot lower than MIG. This means that duty cycle is normally not as critical as it may be for MIG. 

Welding Machines - What is Duty Cycle & How is it Calculated?

From this aspect - a duty cycle of 30% (in the case of MMA) could be considered to be "high".  For example the Weldforce WF-135S is the smallest MMA/stick machine in the Weldclass range (140 amps max output), but with a duty cycle of 100A @ 60% it has enough power to run regular 2.6mm electrodes almost non-stop and will also easily run a 3.2mm electode.

Exceptions to this - stick/MMA applications that require very high duty cycle - can include hard-facing, where each electode is run in quick succession with very little "time out".

Duty Cycle & TIG welding

When it comes to TIG, the importance of duty cycle can vary considerably.

TIG is commonly used for detailed work on thinner materials and/or smaller parts. In this case, the machine will often never even come close to reaching it's duty cycle limit... and indeed a lot of welding is done at low amperage where the machine may have a duty cycle of 100%.  Also, because TIG is a manual process (where the filler metal is fed by hand), the "welding/on time" vs "off time" ratio is lower (compared to MIG).

However, there are some TIG applications where a high duty cycle becomes very important. One example of this is TIG welding of pipe joints where a long, continuous weld is required.

Comments & Questions?

Got your own thoughts or questions on duty cycle?  Feel free to submit a comment below ↓, or click here send us an equiry.

More articles on inverter welders;

What is an inverter welder & how does it work?

Using Generators to power Inverter Welders

What is Hot Start, Arc Force & Anti-Stick?

Welding Machines - What is Duty Cycle & How is it Calculated?

All welding machine articles

Weldforce welding machine range by Weldclass

While all care has been taken, Weldclass accepts no responsibility for any inaccuracies, errors or omissions in this information or links and attachments. Any comments, suggestions & recommendations are of a general nature only and may not apply to certain applications. It is the sole responsibility of the user and/or operator to select the appropriate product for their intended purpose and to ensure that the product selected is capable of performing correctly and safely in the intended application. E.&O.E.

Welding Machines - What is Duty Cycle & How is it Calculated?

That's the session will be useful for those who read it. Thank you for your visit

posting sourced from

Don't forget to bookmark "Welding Machines - What is Duty Cycle & How is it Calculated?" using Ctrl + D or Command + D (Macos). You can share this posting using the share button.

Post a Comment for "Welding Machines - What Is Duty Cycle & How Is It Calculated? Define Welding Duty Cycle"