Skip to content Skip to sidebar Skip to footer

Widget Atas Posting

SMPS Welding Inverter Circuit | Homemade Circuit Projects

Hallo ! Welcome to the a domain all about welder, This a domain was created as a means to provide a variety of instructions, especially relating to welder pursuits. on this occasion me will discuss approximately"SMPS Welding Inverter Circuit | Homemade Circuit Projects" distinctly, get moving see in detail...

SMPS Welding Inverter Circuit | Homemade Circuit Projects

SMPS Welding Inverter Circuit | Homemade Circuit Projects

If you are looking for an option to replace conventional welding transformer, the welding inverter is the best choice. Welding inverter is handy and runs on DC current. The current control is maintained through potentiometer.

SMPS Welding Inverter Circuit | Homemade Circuit Projects

By: Dhrubajyoti Biswas

Using Two Switch Topology

When developing a welding inverter, I applied forward inverter with two switches topology. Here the input line voltage traverses through the EMI filter further smoothing with big capacity.

SMPS Welding Inverter Circuit | Homemade Circuit Projects

However, as the switch-on current pulse tends to be high there needs the presence of softstart circuit. As the switching is ON and the primary filter capacitors charges via resistors, the power is further zeroed by turning the switching ON the relay.

The moment the power is switched, the IGBT transistors gets used and are further applied through TR2 forward gate drive transformer followed by shaping the circuit with the help of IC 7812 regulators.

Using IC UC3844 for PWM Control

The control circuit used in this scenario is UC3844, which is very much similar to UC3842 with pulse-width limit to 50% and working frequency to 42 kHz.

The control circuit draws the power from an auxiliary supply of 17V. Due to high currents, the current feedback uses Tr3 transformer.

The voltage of 4R7/2W sensing register is more or less equal to the current output. The output current can be further controlled by P1 potentiometer. Its function is to measure the feedback’s threshold point and the threshold voltage of pin 3 of UC3844 stands at 1V.

One important aspect of power semiconductor is that it needs cooling and most of the heat generated is pushed out in output diodes.

The upper diode which consists of 2x DSEI60-06A should have the capacity to handle the current at an average of 50A and loss till 80W.

The lower diode i.e. STTH200L06TV1 also should the average current of 100A and loss till 120W. On the other hand, the total max loss of the secondary rectifier is 140W. The L1 output choke is further connected with the negative rail.

This is a good scenario since the heat sink is barred from hi-frequency voltage. Another option is to use FES16JT or MUR1560 diodes.

However, it is important to consider that the max current flow of the lower diode is twice the current to that of the upper diode.

Calculating IGBT Loss

As a matter of fact, calculating IGBT’s loss is a complex procedure since besides conductive losses switching loss is another factor too.

Also each transistor loses around 50W. The rectifier bridge also loses power till 30W and it is placed on the same heat sink as IGBT along with UG5JT reset diode.

There is also the option to replace UG5JT with FES16JT or MUR1560. The loss of power of the reset diodes is also dependent upon the way Tr1 is constructed, albeit the loss is lesser compared to the loss of power from IGBT. The rectifier bridge also accounts to power loss of around 30W.

Furthermore when preparing the system it is important to remember to scale the maximum loading factor of the welding inverter. Based upon the measurement, you can then be ready to select the correct size of the winding gauge, heat sink etc.

Another good option is to add a fan as this will keep a check on the heat.

Circuit Diagram

Transformer Winding Details

The Tr1 switching transformer is wounded two ferrite EE core and they both have the central column section of 16x20mm.

Therefore, the total cross section calculates to 16x40mm. Care should be taken to leave no air gap in the in the core area.

A good option would be to use 20 turns primary winding by wounding it with 14 wires of 0.5mm diameter.

The secondary winding on the other hand has six copper strip of 36x0.55mm. The forward drive transformer Tr2, which is designed on low stray inductance, follows trifillar winding procedure with three twisted insulated wire of 0.3 mm diameter and the windings of 14 turns.

The core section is made of H22 with the middle column diameter of 16mm and leaving no gaps.

The current transformer Tr3 is made of EMI suppression chokes. While the primary has only 1 turn, the secondary is wounded with 75 turns of 0.4 mm wire.

One important issue is to keep the polarity of the windings. While L1 has ferrite EE core, the middle column has the cross section of 16x20mm having 11 turns of copper strip of 36x0.5mm.

Furthermore, the total air gap and the magnetic circuit are set to 10mm and its inductance is 12uH cca.

The voltage feedback does not really hamper the welding, but it surely affects the consumption and the loss of heat when in idle mode. The use of voltage feedback is quite important because of high voltage of around 1000V.

Moreover, the PWM controller is operating at max duty cycle, which increases the power consumption rate and also the heating components.

The 310V DC could be extracted from the grid mains 220V after rectification via a bridge network and filtration through a couple of 10uF/400V electrolytic capacitors.

The 12V supply could be obtained from a ready-made 12V adapter unit or built at home with the help of the info provided here:

Aluminum Welding Circuit

This request was submitted to me by one of the dedicated readers of this blog Mr. Jose. Here are the details of the requirement:

My welding machine Fronius-TP1400 is fully functional and I have no interest in changing its configuration. This machine that has an age is the first generation of inverter machines.

It is a basic device for welding with coated electrode (MMA welding) or tungsten arc gas (TIG welding). A switch allows the choice.

This device only provides DC current, this is very appropriate for a large number of metals to be welded.

There are a few metals such as aluminum that due to its rapid corrosion in contact with the environment, it is necessary to use pulsating AC current (square wave 100 to 300 Hz) this facilitates the elimination of corrosion in cycles with inverted polarity and turn the melting in the direct polarity cycles.

There is a belief that aluminum does not oxidize, but it is incorrect, what happens is that at the zero moment that it receives contact with air, a thin layer of oxidization is produced, and which from then on preserves it from next subsequent oxidization. This thin layer complicates the work of welding that's why AC current is used.

My desire is make a device that be connected it betwen the terminals of my DC welding machine and the Torch to obtain that AC current in the Torch.

This is where I have difficulties, at the moment of building that CC to AC converter device. I am fond of electronics but not expert.

So I understand the theory perfectly, I look at the HIP4080 IC or similar datasheet seeing that it is possible to apply it to my project.

But my great difficulty is that I do not do the necessary calculation of the values of the components. Maybe there is some scheme that can be applied or be adapted, I not find it on internet and I do not know where to look, that's why I ask for your help.

The Design

In order ensure that the welding process is able to eliminate the oxidized surface of an aluminum and enforce an effective welding joint, the existing welding rod and the aluminum plate could be integrated with a full bridge driver stage, as shown below:

welding aluminum by eliminating oxidization

The Rt, Ct could be calculated with some trial and error to get the mosfets oscillating at any frequency between 100 and 500Hz. For the exact formula you could refer to this article.

Th 15V input could be supplied from any 12V or 15V AC to DC adapter unit.

About Swagatam

I am an electronic engineer (dipIETE ), hobbyist, inventor, schematic/PCB designer, manufacturer. I am also the founder of the website: https://www.homemade-circuits.com/, where I love sharing my innovative circuit ideas and tutorials.

If you have any circuit related query, you may interact through comments, I'll be most happy to help!

SMPS Welding Inverter Circuit | Homemade Circuit Projects

That's the seminar will be useful for those who read it. Thank you for your visit

content sourced from https://www.homemade-circuits.com/smps-welding-inverter-circuit/

Don't forget to bookmark "SMPS Welding Inverter Circuit | Homemade Circuit Projects" using Ctrl + D or Command + D (Macos). You can share this content using the share button.

Post a Comment for "SMPS Welding Inverter Circuit | Homemade Circuit Projects"

Berlangganan via Email